Repair parts OnePlus 15R

OnePlus 15R parts for models CPH2767 and CPH2769

The OnePlus 15R was unveiled in December 2025 as the international version of the Chinese Ace 6T, with a 6.83-inch 165 Hz AMOLED screen, ultrasonic fingerprint reader and 7,400 mAh battery. In this category, you can find the screen assembly, the rear cover with camera frame and the USB charging port, which we currently offer in Original quality. Below, we explain what to check on your device before choosing each part, as the colour and disassembly sequence affect your purchase for this model.

The OnePlus 15R shares its design with the Ace 6T, but they are not the same phone

The OnePlus 15R units sold in Europe and most international markets have the model codes CPH2767 and CPH2769. Both refer to the same device, with Snapdragon 8 Gen 5, 12 GB of RAM and the same 6.83-inch screen, and are assigned to different regions. You can find the code in your phone's settings, in the device information section, or on the box label.

The most common point of confusion is the OnePlus Ace 6T, the Chinese version from which it is derived. It shares the screen size and 165 Hz refresh rate, but has an 8,300 mAh battery instead of 7,400 mAh, so you should not assume that all its internal parts fit the 15R. Do not confuse it with the OnePlus 15 either: its rear camera module includes a telephoto lens, whereas the 15R has only two cameras (50 MP main and 8 MP ultra-wide), so the rear covers and camera frames are not interchangeable between the two.

The OnePlus 15R has a 6.83-inch LTPS AMOLED with an ultrasonic fingerprint reader beneath the glass

The OnePlus 15R panel is a 6.83-inch LTPS AMOLED with a resolution of 2800 x 1272 pixels, Gorilla Glass 7i and a refresh rate of up to 165 Hz. As it is LTPS rather than LTPO, the minimum refresh rate remains at 60 Hz; this is how it works from the factory and is worth bearing in mind so you do not attribute it to the replacement part after repair. The fingerprint reader is ultrasonic and reads through the panel, so the screen is an integral part of the unlocking system.

The complete screen for OnePlus 15R is currently available in Original quality, the top range of the replacement parts market and the equivalent of the original panel, with its brightness, high-frequency touch response and compatibility with the ultrasonic reader. Bear in mind that the 15R screen is replaced from the rear: to access its connector, you need to remove the rear cover, the lower cover and the sub-board, then seal the panel with new adhesive. When pricing up a screen replacement, it is therefore worth checking the condition of the rear cover and charging port during the same repair.

The OnePlus 15R rear cover is adhesive-fitted and its material varies by colour

The OnePlus 15R rear cover is not secured with screws: it is held in place with adhesive and removed by applying heat, with a risk of the glass cracking as it is lifted off. The Charcoal Black and Mint Breeze finishes have a glass rear cover, while the Ace Edition Electric Violet uses a fibreglass rear cover. Check your phone's finish before ordering the part and check the available colour on the product page.

The complete OnePlus 15R rear cover with camera frame is currently sold in Original quality and comes with the dual-camera module frame already fitted, so you do not need to recover the trim from the damaged cover. The rear cover contributes to the sealing that gives the 15R its IP66, IP68, IP69 and IP69K ratings; any replacement requires new adhesive, and the final water resistance depends on the installation, not just the part.

The OnePlus 15R USB-C 2.0 port is on a screwed-in lower sub-board

The OnePlus 15R connector is USB-C 2.0 and supports SuperVOOC charging at up to 80 W. According to the published teardown of the model, the port is on a lower sub-board, accessed after removing the rear cover and a cover secured with standard Phillips screws, with no proprietary screws.

The Original USB charging port for OnePlus 15R is available in Original quality, suitable for a connector that handles high currents during fast charging. As the same sub-board is removed to access the screen connector, if you are replacing the panel or rear cover, it is worth checking the port during the same repair and avoiding having to lift the rear cover twice.

Frequently asked questions about repairing a OnePlus 15R CPH2767 or CPH2769

Do OnePlus Ace 6T parts fit the 15R?

They share the same design and 6.83-inch 165 Hz screen, and replacement screens suitable for both models are available on the market. However, the battery is different (8,300 mAh in the Ace 6T compared with 7,400 mAh in the 15R). The parts in this category are listed for the 15R, so always check your device's model code before purchasing.

Will the ultrasonic fingerprint reader still work after replacing the OnePlus 15R screen?

On other OnePlus models with an ultrasonic reader, there have been cases where the sensor needs to be recalibrated from the device's service menu after a new screen is installed. There is no specific information about the 15R to confirm whether this is always required, so bear this in mind when preparing for the repair and update OxygenOS before you begin.

Will the OnePlus 15R retain its IP69K rating after being opened?

This cannot be guaranteed. The original water resistance depends on the factory seals on the rear cover and screen, and new adhesive must be applied after any opening. The final result depends on how the device is resealed.

How can I tell whether my rear cover is glass or fibreglass?

It depends on the colour: Charcoal Black and Mint Breeze have glass, while the Ace Edition Electric Violet has fibreglass. If you are unsure, compare your device's finish with the rear cover product page before ordering.