Repair parts Google Pixel 10 Pro XL
Receive it on monday 02 de november
This category includes spare parts for the Google Pixel 10 Pro XL, the 6.8-inch model Google launched in late August 2025 alongside the Pixel 10 Pro. It is one of the easiest Pixel phones to repair: the battery can be removed using pull tabs, and Google has published a free 234-page service manual. Below, we explain how to check your variant and what to bear in mind for each part in the catalogue.
Google Pixel 10 Pro XL: G45RY, GUL82 and GYPW4 codes and differences from the Pixel 10 Pro
The Pixel 10 Pro XL is sold under three hardware codes, G45RY, GUL82 and GYPW4, which correspond to regional variants of the same phone. Google's official parts for this model are listed as compatible with all three, so you do not need to distinguish between them when choosing a screen, battery or back cover. To check which one you have, open Settings > About phone and go to the regulatory labels section; if the phone will not start, you can identify it using the IMEI.
The usual source of confusion is the Pixel 10 Pro, which shares the same design, Tensor G5 processor and triple rear camera. However, its screen is 6.3 inches and its battery is 4870 mAh, compared with the XL's 6.8 inches and 5200 mAh, so the screen, battery and back cover are not interchangeable between the two. Wired charging also differs: 45 W for the XL and 30 W for the Pro.
The Pixel 10 Pro XL's 6.8-inch Super Actua panel has an integrated under-display fingerprint reader
The Pixel 10 Pro XL has a 6.8-inch Super Actua LTPO OLED panel, with a resolution of 1344 x 2992 pixels, a variable refresh rate of 1 to 120 Hz and peak brightness of 3300 nits. The fingerprint reader sits beneath the screen, and Google's official replacement assembly comes with the reader already fitted.
In this catalogue, you will find the complete screen for Google Pixel 10 Pro XL, currently available in Original quality. As this is a complete module, there is no need to separate the glass and panel from the faulty assembly. According to published teardowns, the screen connects via a single flex cable secured by a metal clip, with no additional screws, reducing the risk of damaging the connector during installation.
One thing to plan for is fingerprint calibration: after fitting a new screen, Google recommends calibrating the sensor using its Pixel Repair Tool web tool, with the phone connected to a computer. Also note that this panel is exclusive to the XL and is not compatible with the Pixel 10 Pro.
5079 mAh nominal capacity and pull tabs: the Pixel 10 Pro XL's GD1J6 battery
The Pixel 10 Pro XL battery has the reference GD1J6 and a nominal capacity of 5079 mAh (19.76 Wh at 3.89 V). Google lists 5200 mAh as the phone's typical capacity; both figures refer to the same battery, so it is not an error if the replacement shows 5079 mAh. If you find batteries with different capacities for sale, check that they are not for the Pixel 10 Pro.
The GD1J6 5079 mAh battery for Pixel 10 Pro XL is currently available in Premium quality: a compatible part for Google Pixel 10 Pro XL at a lower price than Google's original battery. Its designation includes the same reference and nominal capacity as the manufacturer's part.
Replacement is easier than on previous versions: Google has replaced the strong adhesive with pull tabs, allowing the battery to be removed without heat or solvents. Access is from the back, by removing the back cover, so it is advisable to have new adhesive ready to reseal it. Google also recommends a calibration cycle for the new battery: charge it fully, discharge it completely, then recharge it to 100% without pauses.
The Pixel 10 Pro XL's back cover is removed with heat and is connected by a flex cable
The back of the Pixel 10 Pro XL is made of Gorilla Glass Victus 2 and is glued to the frame: it can be removed with heat and a suction cup, without the need for a laser. One particular feature is that a flex cable connects the cover to the phone beside the power button, and it should be disconnected before removing the cover completely.
The complete back cover with camera frame for Pixel 10 Pro XL, currently available in Original quality, includes the camera bar frame, so it replaces in a single part any damage affecting both the back glass and the lens area. If the cover is still intact and only the camera glass is broken, the alternative is the rear camera lens and frame for Pixel 10 Pro XL, a smaller, lower-priced part.
Google's official back cover is shipped without adhesive, so check whether you need new adhesive. The phone leaves the factory with an IP68 rating, but after it has been opened, its water resistance depends on how the adhesive is applied and how clean the frame is.
Other Google Pixel 10 Pro XL components: 42 MP front camera, USB-C, flex cables and audio
The rest of the range covers more specific faults. On the Pixel 10 Pro XL, the charging connector is on a separate USB-C board, while the front camera offers 42 MP resolution, the same as on the Pixel 10 Pro, although Google lists it as a different part for each model. All the parts listed here are available in Original quality:
- 42 MP front camera for Pixel 10 Pro XL.
- USB charging port for Pixel 10 Pro XL.
- Power and volume button flex cable.
- Antenna flex cable.
- Flex cable to motherboard for Pixel 10 Pro XL.
- Main speaker for Google Pixel 10 Pro XL.
- Earpiece speaker for Pixel 10 Pro and Pixel 10 Pro XL: this is the only part in this category listed as compatible with both models.
Fingerprint calibration, battery health and IP68 on the Google Pixel 10 Pro XL
Do I need to recalibrate the fingerprint reader after replacing the Pixel 10 Pro XL screen?
Yes. Google provides a way to calibrate the in-screen reader using Pixel Repair Tool, a tool that runs in the Chrome browser while the phone is connected via USB and booted in fastboot mode. If you work in a repair shop, allow for this step in the repair time.
How can I check whether my Pixel 10 Pro XL battery needs replacing?
In Settings > Battery > Battery health, the system shows whether capacity is Normal or Reduced; Google considers a battery below 80% to be Reduced. On Pixel phones from the 8a onwards, including this model, the battery is designed for 1000 cycles, which you can check under About phone > Battery information.
The screen stops responding to touch after being inactive for a while. Is it faulty?
Not necessarily. Various Pixel 10 Pro XL users have reported that the touchscreen stops working while the phone is idle and starts working again after a restart, while the rest of the phone continues to operate. If touch works again after restarting, check for software updates before ordering a new screen.
Is the Pixel 10 Pro battery compatible with the Pixel 10 Pro XL?
No. The Pixel 10 Pro has a 4870 mAh battery, while the XL uses the GD1J6 with a nominal capacity of 5079 mAh; they are different parts. Always order the part made for the XL.
