Huawei P40 Lite 5G screen: what to know before opening your phone
You drop your phone, turn it over and see the crack. The first question is usually how much it will cost to fix. At iLevante, we prefer to start with another question: what exactly is broken? Let’s take it step by step, because sometimes the damage is not as bad as it looks.
P40 Lite screen: how to tell what has failed
Take a good look at your phone and see which of these four cases applies:
- Crack, but the image and touchscreen work perfectly. Try lifting the screen protector at one corner. The crack may come off with it, making the repair free. If it is still there, the front glass is cracked. It is bonded to the LCD, so the complete assembly needs replacing.
- Black spots or coloured lines. The LCD panel has been damaged, and the problem is likely to get worse.
- It rings and vibrates, but the screen stays black. The problem may be with the LCD or its connection to the motherboard. The rest of the phone is probably still working.
- The screen taps by itself or ignores part of your touch. This needs a little more investigation, as the screen is not always to blame.
For this last case, there is a very useful test recommended by Huawei:
- Tap Build number seven times in the system settings to enable Developer options.
- Turn on Pointer location.
- Slowly move your finger across the entire screen.
Watch the line you draw. If it always breaks in the same place, the touchscreen is likely faulty. A continuous line points to another cause, such as a frozen app, a charger from another brand or a screen protector that is too thick. It is also worth turning off Glove mode, which increases sensitivity and can cause problems when you use your phone without gloves.
Huawei P40 Lite 5G screen compatibility
This is an easy mistake to make when ordering, because two phones have almost identical names. The P40 Lite 4G has a 6.4-inch screen with a resolution of 2310 x 1080 pixels. The 5G model has a 6.5-inch screen and a resolution of 2400 x 1080. That extra tenth of an inch is enough to make one module incompatible with the other.
This part is for model CDY-NX9A. You can find the model number under Settings > About phone. If the screen is unusable, check the original box instead.
One interesting detail: in practice, the P40 Lite 5G is a nova 7 SE rebranded for Europe. They look almost identical, but we list this replacement part only for the CDY-NX9A, so do not assume it will fit a nova.
What you get with your P40 Lite 5G screen
This is a new, complete module that has passed two quality checks. It includes the front glass, touchscreen, LCD, flex cable, display controller and backlight. It comes in black, which is the colour of the front you will see even if your phone is Crush Green or Space Silver.
The box also includes a free screen protector and a tool kit with pry tools, a pick and screwdrivers. The price shown on the product page includes taxes; delivery is the only additional cost. Orders placed in time are dispatched the same day. You can add screen adhesive to your order, and we recommend doing so.
Premium quality and brightness: 430 nits explained
This is a Premium-quality IPS LCD panel with a 6.5-inch display, 2400 x 1080-pixel resolution, 405 ppi and a 60 Hz refresh rate. Its brightness is around 430 nits peak and 410 nits average.
What do those figures mean? Nits measure the light emitted by the screen. In a well-lit room, automatic brightness will operate well below that maximum; the highest brightness is mainly useful outdoors. The 405 ppi figure tells you how many pixels fit into each inch. At this pixel density, small text in a message looks sharp at a normal viewing distance.
As this is an LCD, a layer of light illuminates the entire panel from behind. That is why an impact can cause dark spots that spread, and why this type of screen does not suffer from the permanent marks typical of OLED displays.
How to replace the Huawei P40 Lite 5G screen, step by step
The iLevante team has put together this guide so you know what to expect. The repair is moderately difficult: allow at least half an hour, or an hour if it is your first time. You will work from the back of the phone, as the screen connector is on the motherboard. The order or number of screws may vary slightly between devices, so check carefully before pulling anything out.
- Switch off the phone and remove the SIM tray.
- Warm the edges of the back cover with a hairdryer to around 50°C. More heat will not help, and the battery is underneath. Handle the cover as if it were glass, insert the pick at the edge and work slowly around the cameras.
- Remove the screws and place them on a sheet of paper in the same positions as on the phone. Watch out for stickers, as one may be hiding a screw.
- Disconnect the battery before anything else. Use a plastic pry tool, never a metal one. This helps prevent most short circuits.
- Disconnect the screen flex cable from the motherboard. You may need to remove the battery to reach it. Work slowly, without bending or puncturing the battery.
- Warm the edges of the screen and lift it with the pick. There is usually a thin plastic frame between the screen and the chassis. Slide the pick between the screen and this frame, never between the frame and the chassis.
- Clean off all the old adhesive with a soft cloth and isopropyl alcohol. Never use water.
- Test the screen before sticking it down. Connect the new screen and the battery, switch on the phone and repeat the Pointer location test.
- Apply the adhesive and close the phone, pressing down evenly. Fit the screen protector last, once everything is working and there is no dust in sight.
Step 8 can save you a lot of trouble. Imagine sticking the screen down, closing the phone and then finding out that the flex cable was not properly connected: you would have to heat everything up again and remove the screen. Test it first and you can sort out any issues in a minute.
Problems after installing the P40 Lite 5G screen
Almost every problem that can occur has a simple explanation. These are the first things to check:
- The fingerprint sensor stops responding. On this model, the reader is built into the power button on the right-hand side, so it does not depend on the screen and does not need the calibration required by in-display fingerprint readers. Check that the button flex cable is still properly connected and that you did not move it during disassembly.
- The screen is black when you first switch on the phone. Disconnect the battery and reconnect the screen flex cable, making sure it is properly seated. A connector that is not fully inserted is the most likely cause.
- Ghost touches happen only while charging. Try using a Huawei charger and cable before suspecting the replacement screen.
- Touch response feels sluggish when swiping. Remove the screen protector and compare. A thick protector can reduce sensitivity, and even the factory-fitted protector on this phone slightly affected gestures.
- The image looks less sharp. Open the display settings and check the resolution. The Smart Resolution feature switches between HD and FHD, and may be lowering the quality to save battery.
• Product Weight: 0.18 kg.The technical specs of Huawei P40 lite 5G
can help you to choose the correct repair part for your device. Make sure your model reference is the same as this element. Here are some tech specs to help you:
- Brand: Huawei
- Huawei P40 lite 5G Size: 162.3 x 75 x 8.6 mm.
- Release date: 2020, May 15. Released 2020, May 28.
- Weight: 189 g.
- Screen specs: IPS LCD, HDR10.
- Screen size: 6.5 inches, 102.0 cm2.
PVP:
SNK.SPS022816.75€ AvailableInStockNewCondition